Softrock Lite II Home - Softrock Lite II RX
Band: 20m

Introduction

 

Announcement - Official Site

This site is now the officially maintained site for the Softrock Lite II kit.  The previous documentation on www.wb5rvz.com is no longer being maintained.  If you are curious, you can still pop over to the previous site to see the original documentation, but be advised that it is no longer being maintained there.

This set of builders notes is replaces and supercedes the notes for the original SR Lite II design, now documenting a combined kit with all of the components required to do any of the five available options (post 1 Jun1 2010). The original design's schematic dates back to December 2009. The current design's schematic is depicted in the Schematic Section, below.

The Softrock Lite II, the sequel to the SR Lite V6.2 series , provides an economical entry-level kit for the ham or SWL who wants to experiment with Software Defined Radio (SDR).

The Lite II circuit board size is 2.5 inches by 0.9 inches. All SMT components are mounted on the bottom of the board .

Ordering Information

Prices and availability of the kit are found at the Softrock Ordering Website.

This kit was originally offered in several versions, corresponding to bands of interest. It has, since, changed over to the Combined Lite II. This "combined" kit will include all components needed to build the kit as a 160m, 80m, 40m, 30m, or 20m receiver. The 15m option is no longer offered. The builder can decide which kit to build at commencement of the build; the parts for any of the options are included in the shipment. The Combined Lite II kit will be priced at $20 plus $1 for US postage or $2 for DX postage.

As of 11 June, 2010, the options in this series will include:

    40m kit option (the example used herein)
    • 40m kit will tune the following ranges:
    • 40m when used with a soundcard that samples at 48 kHz - 7.032 to 7.08 MHz
    • 40m when used with a soundcard that samples at 96 kHz - 7.008 to 7.104 MHz
  • 80m kit option
    • 80m kit will tune the following range:
    • 80m when used with a soundcard that samples at 48 kHz - 3.49825 to 3.54625 MHz
    • 80m when used with a soundcard that samples at 96 kHz - 3.47425 to 3.57025 MHz
  • 160m kit option
    • 160m kit will tune the following range:
    • 160m when used with a soundcard that samples at 48 kHz - 1.819 to 1.867 MHz
    • 160m when used with a soundcard that samples at 96 kHz - 1.795 to 1.891 MHz
  • 30m kit option
    • 30m kit will tune the following range:
    • 30m when used with a soundcard that samples at 48 kHz - 10.100 to 10.148 MHz
    • 30m when used with a soundcard that samples at 96kHz - 10.076 to 10.172 MHz
  • 20m kit option
    • 20m kit will tune the following range:
    • 20m when used with a soundcard that samples at 48 kHz - slightly below 14.024 to 14.070 MHz
    • 20m when used with a soundcard that samples at 96 kHz - slightly below 14.00 to 14.094 MHz
  • The 30m and 20m kits will all make use of 1/3 sub- harmonic sampling.

Prices for these kits are found at the Softrock Ordering site.


Original Versions of SR Lite II

Before the current Combined SRLite II, the SR Lite II came in six versions corresponding to the 160, 80, 40, 30, 20, and 15m bands. These versions were described in the common schematic, which had a table of band-specific component values. The changes from that schematic to the current version are summarized below:

  • Drop 15m option
  • X1 now 14.089MHz for 80m.
  • C8/C9 no longer band-specific; now 390 pF
  • R7/R8 no longer band-specific; now 4.99k
  • R5 and R6 are now band-specific (49.9Ω on 160, 80, 40; 10Ω on 30, 20)
  • Toroids all go to T30-6
  • New L1 and T1 winding info for all (all have same uH as original versions, except 30m T1, which goes to 0.18 uH)
  • U4 no longer band-specific - it is LT6231 in all options
Original SR Lite II Builders Notes

The original notes were compiled into a PDF file by Philippe F6CZV for those who are still working with the original, now superceded SR Lite (non-combined) kit. Please note that the design of that original kit and the currently offered (from KB9YIG) kit is quite different. Don't get them confused!

Note: SoftRock IF Lite II

Tony also offers several versions of the Softrock Lite II kit that provide panadaptor capability on a number of popular legacy transceivers by tapping into the IF. The versions and the associated IF frequencies are outlined in the table below:

Rig IF Freq Xtal Freq SR Lite Freq
455kHz 1.856 MHz 464 kHz
4.195 MHz 19.6875 MHz 4.921 MHz
8.215 MHz 32.768 MHz 8.192 MHz
8.83 MHz 35.2512 8.812 MHz
9.015 MHz 11.981 MHz 8.985 MHz
(1/3 subharmonic sampling)
10.695 MHz 14.2764 MHz 10.707 MHz
(1/3 subharmonic sampling)
10.707 MHz 14.299 MHz 10.724 MHz
(1/3 subharmonic sampling)

The schematic for this SR IF Lite II kit is essentially the same as the schematic of the SR Lite II combined kit documented herein and these build notes can be used for the IF version. 

(Components required for specific IF options are now included in the printed BOMs in these notes.)

Video of Build for 30m Option

Alan Wolke, W2AEW, has an excellent video showing his build of the 30m option of this kit. Excllently and informatively done, it is worth the watch:

Printable PDF of Build Notes

Click here to download a printable pdf file of the build notes (as of 3/22/2011_

General Info

This kit is for the 20m band and it will tune the following calculated range based upon a crystal frequency of 18.73 MHz:

  • When used with a soundcard that samples at 48 kHz (and doesn't have a lowpass filter cutoff below 24 kHz): 14.0235 - 14.0715
  • When used with a soundcard that samples at 96 kHz (and doesn't have a lowpass filter cutoff below 48 kHz): 13.9995 - 14.0955

Theory of Operaton

Many thanks to Jan G0BBL and Tony KB9YIG for their input to this and the stages' theoretical discussions.

  • This 20m receiver is patterned on the classic "direct conversion" receiver, in that it mixes incoming RF down to audio frequencies by, in effect, beating the RF against a Local oscillator such that the mixer products are in the sub 100 kHz range.
  • Unlike the traditional DC receiver, the SDR does not "tune" the local oscillator's frequency to beat up against a desired RF signal. Instead, the local oscillator is at a fixed frequency of 18.73 MHz.
  • As a result, the (baseband) mixer products can vary in frequency from zero to +/- some theoretically high super-audio frequency. In fact, the practical limit is one-half the soundcard's maximum sampling rate.
  • The "tuning" (and demodulation and AFC and other neat radio things) happen in the software part of the Software Defined Radio. It is the magic of Software that makes for the extraordinarily high selectivity in the direct conversion hardware (which is notorious for great sensitivity but terrible selectivity).
  • The software requires the mixer's baseband products to be provided to the PC as two separate signals, each identical to the other, except that they are 90 degrees apart in phase ("in quadrature"). The SR Lite II achieves this by dividing the local oscillator's frequency by 4 (with attendant phase shifts to achieve quadrature).
  • The output of the divider chain is two signals, I (In-Phase) and Q (Quadrature), identical in all respects but phase i.e., they are "in quadrature"). For this 20m option, their frequency is 4.6825 MHz
  • RF from the antenna is bandpass-filtered for the 20m band.
  • The two quadrature signals from the Divider stage are fed into the mixer stage. The 4.6825 MHz quadrature signals from the divider in the 20m option are rich in harmonics. The third harmonic (14.0475) is what is actually used in the mixer stage.
  • The mixer stage mixes the bandpass-filtered RF down to two baseband signals that are also in quadrature and otherwise identical to each other.
  • The two baseband signals are provided to an amplifier stage where they are amplified and low-pass filtered to levels acceptable to the PC's soundcard stereo line-in inputs.
  • A soundcard which can sample 48 kHz, can digitize an incoming "chunk" of baseband signals from 0 to 24 kHz. Such a soundcard, using its stereo line-in inputs for the I and Q signals, will yield an effective bandwidth of 48 kHz: 24 kHz above the center frequency and 24 kHz below the center frequency. The SDR software in the PC manipulates the digitized I and Q signals to deliver, demodulate, condition, and filter signals within this 48 kHz spectrum. Soundcards capable of higher sampling rates (e.g. 96 kHz or 192 kHz) will yield proportionately wider bandwidth, provided their internal audio filters do not cut off the higher audio frequencies.
  • Mike Collins KF4BQ (whose photos of the completed board are found further on in this page) has performed extensive tests on this receiver and has found it to be an exceptionally powerful receiver. Considering the cost, nothing out there can beat it!

Schematic

main schematic

Board Layouts

Topside

topside layout

Underside

undersideside layout

Build Stages

This kit is built in stages, with each stage being testable upon completion.

The stages in the build are, in build order:

Completed Images

Note: the completed pictures are of the 40m option, which the author built. Other band options (which the author did not build) will appear slightly different (especially the inductors, whose windings and cores will vary by band) for the band-specific components.

Topside

completed topside

Underside

completed underside Local Oscillator Stage Dividers Stage Power Supply Stage Band Pass Filter Stage Mixer Stage Op Amp Stage